Showing posts with label Needle. Show all posts
Showing posts with label Needle. Show all posts

Wednesday, September 27, 2017

Needles
The needles are the most important stitch forming elements. They are displaced vertically up and down and are mounted into the tricks or cuts of the knitting cylinder. There are three types of needles namely:

  1. Latch needle
  2. Spring bearded needle
  3. Compound needle.
We can divide a needle into three main parts:

  • The hook; which takes and retains the thread tube looped.
  • The hook opening and closing device; that allows the hook to alternatively take a new thread and release the previous one.
  • A system allowing the needle to move and form the loop.


Fig: Needle;  1=Butt, 2=Butt height, 3=Back shank, 4=Stem, 5=Crimp, 6=Groove, 7=Cheek, 8=Hook, 9=Hook width, 10=Latch, 11=Rivet 
Sinker
The sinker is the second primary knitting element. It is a thin metal plate with an individual or a collective action operating approximately at right angles from the hook side of the needle bed, between adjacent needles. Sinkers capable of producing loop fabric are well known in the knitting industry. In such machines the sinkers generally include a blade having an upper edge which defines a lower knitting level and a nib having an upper edge which is at an upper knitting level. Long loops are formed at the upper knitting level of the sinkers with a loop yarn and a base yarn is knitted over the blade. The sinkers may be formed and their movement controlled to cause either the loop yarn to appear on one side of a fabric and the base yarn on the other or the loop yarn to appear on both sides. In the past it has not been possible to producing loop cloth of ideal quality since loops would twist or coil making it difficult to finish a loop fabric into satisfactory velor. Furthermore loops which were supposed to appear on the front of a fabric would sometimes appear on the other side. The back of loop cloth was therefore apt to have objectionable loose protruding loops and double tuck stitches.

Fig: sinker; 1=Butt, 2=Butt breadth, 3=Height of shank, 4=Buldge, 5=Neb, 6=Length of neb, 7=Throat angle, 8=Sinker platform height, 9=Breadth of lower shank, 10=Clearance, 11=Throat
    
Sinkers Operation

  1. The held loop is positioned in the throat of the sinker when the sinker moves forward and the needle moves upward for clearing. The held loop is held by the throat and hence its movement along the needle is restricted.
  2. The sinker remains at its forward position when the needle attains its clearing position.
  3. The sinker retracts when the needle comes down after feeding. At this stage, due to sinkers retraction, fabric or held loop is eased out. Also the sinker belly supported the fabric or held loop and hence its movements along the needle is prevented.
  4. Sinker remains in backward position and the needle descends to its lowest position drawing the new loop through the old one.
  5. Before the needle ascends, the sinker moves forward to push the knitted fabric a little and to hold the old loop away from the head of the needle and to be in a position to control the fabric.


Jack
In circular knitting machines of the rotatable cylinder type a well know means for selectively actuating the knitting instrumentalist is that of a pattern controlled slider jack system. Engaged the known type of slider jack system it is common practice to transmit the dictates of the pattern controlled slider jack directly to a needle actuating jack. Circular knitting machines which utilize a slider jack system must have a cylinder of sufficient length to accommodate the circular series of needle, needle actuating jacks and slider jacks which are slid ably mounted in the slots formed on the periphery of said cylinder. The slider jack must be raised a sufficient distance so as to raise the needle actuating jack or intermediate jack to a level where its operating butt will be engaged by a cam member and raise said jack to knitting height which in turn will raise its respective needle to the required height to perform its intended function.

 Dial
Dial is the upper steel needle bed used in double knit machines. Into the grooves of the dial, the needles are mounted horizontally and are allowed to move radially in and out by their dial cams. The number of grooves per unit space conforms to the cylinder gauge in most of the cases.
Fig: dial

CYLINDER
The cylinder is a steel circular bed having grooves/tricks/cuts on its outer periphery into which the needles are mounted. With reference to the tricks, the needles move vertically up and down by their butt being in contact with the cam track. The number of tricks per inch i.e., number of needles per inch decides the gauge of the machine. Machines are built as low as 4 NPI to as high as 32 NPI. Based on the machine gauge, the fineness of the yarn to be knitted can be varied. The diameter of the cylinder also varied based on the type and width of the fabric and a maximum of 75 cm diameter machines are available.

Fig: Cylinder

CAMS
The knitting cams are hardened steels and they are the assembly of different cam plates so that a track for butt can be arranged. Each needle movement is obtained by means of cams acting on the needle butts. The upward movement of the needle is obtained by the rising cams or clearing cams. The rising cam places the needle at a certain level as it approaches the yarn area. Cams controlling the downward movement of the needles are called stitch cams. The stitch cam draws the needle down below the knitting level, thereby drawing a loop formed by the fed yarn through the loop already on the needle. The lowest point to which the needle is drawn by the stitch cam is called the "cast-off" position. They are screwed to the cylindrical cam ring and are adjustable in vertical direction. If the stitch cam is raised, then shorter loop is drawn below the sinker level and a tighter fabric will result. With lowering of stitch cam, a reverse result is obtained. Guard cams keep the needle butts in their race-way. Running cams or the needle butts at a low level until they meet the next rising cam.


Fig: Cams

FEEDERS/STRIPPERS
Feeders are the yarn guides placed close to the needles to the full circumference of the knitting zone. The feeders feed the yarn into the needle hooks and control the needle latches in their open position while the needle attain their clearing position. They consist of a yarn guiding hole and a bevel edge to guard the latches of the approaching needles. They are slightly curved to the corresponding curvature of the needle bed. Feeders may have two holes also for the purpose of plating. Yarn feeders can be divided into “positive” or “negative” types depending on the possibility of controlling the yarn feeding speed and uniformity. The feeder brackets can be adjusted to set their distance from the needle and to ensure yarn feed into needle hooks. Stripers are the feeders designed to deliver two or more yarns individually to the same feed. They can be considered as moving guide replacing the holes of fixed guides. In a two color stripe, two different colored yarns are supplied by two stripper fingers and their engagement is controlled by an endless control chain which governs the guide change at the appropriate feeds. At each revolution, a counter may select the movement of all the striper chains. The stripes are used on both single and double bed machines.


Fig: Feeders/Stripers

Saturday, September 16, 2017

Types of knitting needle
There are mainly three types of needle is used
1.      Latch Needle
2.      Compound Needle
3.      Bearded Needle

Latch Needle
Matthew Townsend, a Leicester hosier, patented the latch needle in 1849.  Townsend spent much of his time developing new knitted fabrics and he investigated a simpler way of knitting purl fabrics.  Purl fabrics required two beds of bearded needles and pressers to alternate the face of loops between courses.  A double-headed latch needle was developed as a result of the research to allow the alternation to be achieved on one bed of needles.  A single-headed latch needle was also developed to provide an alternative to the bearded needle.The latch needle knitting cycle starts with the old loop trapped inside a closed latch.  The needle is pushed up and the old loop slides down the stem, opening the latch in the process.  A thread is then laid in front of the stem between the rivet and the hook.  As the needle is pulled down the hook catches the thread and forms a new loop.  The old loop now slides back up the stem, closes the latch and falls off the end of the needle.  The cycle is then repeated. Latch Needle is mostly used needle in the knitting industry today. Latch needle were used on raschel and crochet machines.

Fif.Latch Needle

Latch Needle Characteristics:
1. Most widely used in weft knitting.
2. More expensive needle than the bearded needle.
3. Self acting or loop controlled.
4. Work at any angle.
5. Needle Depth determines the loop length.
6. Variation of the height of reciprocating produces knit, tuck or miss stitch.

Uses of Latch Needle: Latch needle are widely used in –
1. Double Cylinder Machine,
2. Flat Bar Machine,
3. Single Jersey Circular Knitting Machine,
4. Double Jersey Circular Knitting Machine.

Differents Parts of Latch Needle has been showed below:
1. The Hook: The hook which draws and returns the new loop.
2. The slot or Saw Cut: This slot receives the latch blade.
3. The Cheeks or Slot Walls: It is either punched or riveted to fulcrum the latch blade.
4. The Rivet: The rivet which may be plain or threaded. This has been dispensed with on most plated      metal needles by pinching n the slot walls to retain the latch blades.
5. The latch blade: This latch blade locates the latch in the needle.
6. The latch spoon: The latch spoon is an extension of blade and bridges the gap between the hook         and stem.
7. The stem: The stem of latch needle carries the loop in the clearing on rest position.
8. The Butt: Butt of latch needle enables the needle to be reciprocated.
9. The Tail: The tail is an extension below the butt giving additional supp9ort to the needle and keeping the needle in its trick.

The knitting action of the latch needle
Figure  shows the position of a latch needle as it passes through the cam system, completing one knitting cycle or course as it moves up and in its trick or slot.

1. The rest position: The head of the needle hook is level with the top of the verge of the trick. The loop formed at the previous feeder is in the closed hook. It is prevented from rising as the needle rises, by holding-down sinkers or web holders that move forward between the needles to hold down the sinker loops.

2 Latch opening: As the needle butt passes up the incline of the clearing cam, the old loop, which is held down by the sinker, slides inside the hook and contacts the latch, turning and opening it.

3 Clearing height: When the needle reaches the top of the cam, the old loop is cleared from the hook and latch spoon on to the stem. At this point the feeder guide plate acts as a guard to prevent the latch from closing the empty hook.

4 Yarn feeding and latch closing: The needle starts to descend the stitch cam so that its latch is below the verge, with the old loop moving under it. At this point the new yarn is fed through a hole in the feeder guide to the descending needle hook, as there is no danger of the yarn being fed below the latch. The old loop contacts the underside of the latch, causing it to close on to the hook. 5 Knocking-over and loop length formation. As the head of the needle descends below the top of the trick, the old loop slides off the needle and the new loop is drawn through it. The continued descent of the needle draws the loop length, which is approximately twice the distance the head of the needle descends, below the surface of the sinker or trick-plate supporting the sinker loop. The distance is determined by the depth setting of the stitch cam, which can be adjusted.
Fig. Knitting action of the latch needle.

Compound Knitting Needle
The compound needle consist of two parts, needle body and slider.These two parts are moved independently.
Fig. Compound Needle

Compound Needle is used on most complex knitting:
Compound Needle consists of two separately controlled parts; these are- the open hook and the sliding closing element (tongue, latch, piston, and plunger). The two parts rise and fall as a single unit but at the top of the rise, the hook moves faster to open the hooks and at the start of the fall the hook descends faster to close the hook. It is easier to drive the hooks and tongues collectively form two separate bars as in warp knitting; than to move each hook and tongue individually as in weft knitting. Compound needles were used on tricot machines.
Fig. Knitting and Tucking action ofCompound needle.

Two types of compound needle have been employed in warp knitting machines:
The tubular pipe needle has its tongue sliding inside the tube of the open hook. The open stem “Pusher type” or slide needle has a closing wire or tongue that slides externally along a groove on the edge of the flat hook member.

Bearded needle
A fine steel needle for machine knitting that has a butt at one end and a long, flexible hook at the other that curves back to the shank of the needle. Also known as spring needle. Bearded needles were used on tricot machinesA bearded needle shown with the beard in the open and closed positions. The needle consists of five main parts. 

Fig. Bearded Needle

The main parts of the bearded needle
Stem: The stem of bearded needle around which the needle loop is formed.
The Head: In the head section of bearded needle, the stem is turned into a hook to draw the new loop through the old loop.
The Beard: The beard is the curved downwards continuation of the hook that s used to separate the trapped new loop inside from the old loop.
The Eye or Groove: The eye of groove cut in the stem to receive the pointed tip of the beard when it is pressed.
The shank: The shank of bearded needle may be bent for the individual location in the machine or cast with others in a metal lead.

The knitting action of the bearded needle
The knitting action of the bearded needle has been illustrated in Fig. Depending upon the machine, the needles are set vertically or horizontally. The needle has the disadvantage of requiring a pressing edge to close the bearded hook and enclose the new loop. The presser may be in the form of a bar, blade, verge or wheel, with either the presser or the needle remaining stationary whilst the other element moves towards it.Another feature of bearded needle knitting is that individual loop formation has to be achieved by a loop forming element. This leads to a more complicated knitting action but also provides for a more gentle and careful loop formation.
Fig.  Knitting action of the bearded needle